GB/T 22044-2008 婴幼儿服装用人体测量的部位与方法
作者:标准资料网 时间:2024-05-10 09:27:52 浏览:9372
来源:标准资料网
基本信息
| 标准名称： | 婴幼儿服装用人体测量的部位与方法 |
| 英文名称： | Location and method of infants’anthropometric surveys for garments |
| 中标分类： |
|
| ICS分类： |
|
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会 |
| 发布日期： | 2008-06-18 |
| 实施日期： | 2009-05-01 |
| 首发日期： | 2008-06-18 |
| 作废日期： | |
| 主管部门： | 全国服装标准化技术委员会(SAC/TC 219) |
| 提出单位： | 中国纺织工业协会 |
| 归口单位： | 全国服装标准化技术委员会(SAC/TC 219) |
| 起草单位： | 上海市服装研究所、红黄蓝集团有限公司 |
| 起草人： | 施琴、聂雅渊、许鉴、叶显东、秦威、王宏明 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2009-05-01 |
| 页数： | 平装大16开开/页数：12/字数：9 |
| 计划单号： | 20074143-T-608 |
适用范围
本标准首次发布。
本标准非等效采用美国试验与材料协会标准ASTM D 4910-2007《婴幼儿人体测量标准表，0至24码》（英文版）。
本标准规定了婴幼儿服装用人体测量的部位与方法。
本标准适用于对年龄在24个月及以内的婴幼儿的人体测量。
本标准适用于各类服装及服饰配件所需的婴幼儿人体尺寸数据的测量，但并不是所有的本标准定义的婴幼儿人体尺寸在婴幼儿人体测量和婴幼儿服装生产中都是必需的。
前言
没有内容
目录
没有内容
引用标准
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。
GB/T16160 服装用人体测量的部位与方法
所属分类：
Product Code:SAE J1962
Title:Diagnostic Connector Equivalent to ISO/DIS 15031-3:December 14, 2001
Issuing Committee:Vehicle E E System Diagnostic Standards Committee
Scope:This document supersedes SAE J1962 FEB1998, and is technically equivalent to ISO/DIS 15031-3:December 14, 2001. This document is intended to satisfy the requirements of an OBD connector as required by U.S. On-Board Diagnostic (OBD) regulations. The diagnostic connection specified in this document consists of two mating connectors, the vehicle connector and the external test equipment connector. This document specifies: a. The functional requirements for the vehicle connector. These functional requirements are separated into four principal areas: connector location/access, connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits, b. The functional requirements for the external test equipment connector. These functional requirements are separated into three principal areas: connector design, connector contact allocation, and electrical requirements for connector and related electrical circuits.Differences from ISO Document. The ISO 15031-3 document is intended to satisfy the requirements of OBD requirements in countries other than the U.S., and includes functionality not required or not allowed in the U.S. Notable exceptions are: a. Proposed U.S. OBD regulations specify a connector location that is more restrictive than specified in this document. b. Proposed U.S. OBD regulations do not allow greater than 20 V at the SAE J1962 connector. Only the Type A connector as defined in this document is allowable. Differences between the documents are highlighted in the technical requirements sections of this document. Deleted text is highlighted with strikethrough and new text is highlighted with bold italic. NOTE - To maintain equivalency of the documents, a comma is used as a decimal marker for numeric values in this document.Product Code:SAE AMSR3065
Title:Rubber, Fabricated Products
Issuing Committee:Ams Ce Elastomers Committee
Scope:This specification establishes the requirements for fabricated products of vulcanized rubber, synthetic rubber or rubberlike compositions alone or in combination, together with procedures for the inspection of such products (see 6.1).
